Document Overview
Key Findings The ETENWOLF X6PRO tire inflator successfully inflated a 215/55R17 passenger car tire from 25 psi to 35 psi across all 20 test runs, with both units completing every cycle in under 1 minute 30 seconds. Product: ETENWOLF X6PRO Tire Inflator Test Target: Passenger…
- Document type
- Test Report
- Prepared by
- Daniel Wright
- Published
- Last reviewed
- Topics
- Motor Performance
Key Findings
The ETENWOLF X6PRO tire inflator successfully inflated a 215/55R17 passenger car tire from 25 psi to 35 psi across all 20 test runs, with both units completing every cycle in under 1 minute 30 seconds.
- Product: ETENWOLF X6PRO Tire Inflator
- Test Target: Passenger car tire — 215/55R17
- Pressure Range: 25 psi → 35 psi (10 psi delta)
- Units Tested: 2 samples (Unit 1# and Unit 2#)
- Runs per Unit: 10
- Unit 1# Range: 1 min 20 sec – 1 min 28 sec
- Unit 2# Range: 1 min 18 sec – 1 min 25 sec
- Overall Fastest Run: 1 min 18 sec (Unit 2#, Run 5)
- Overall Slowest Run: 1 min 28 sec (Unit 1#, Run 6)
- Verdict: All runs within consistent performance band — PASS
Test Overview
| Field | Details |
|---|---|
| Test Type | Inflation Efficiency — Time to Inflate |
| Report File | X6pro-充气效率数据2026.2.10.xlsx |
| Sheet | 25-35psi打气时间 (25–35 psi Inflation Time) |
| Test Date | 2026-02-10 |
| Product | ETENWOLF X6PRO Tire Inflator |
| Product Line | Inflation Tools |
| Category | Air Pump / Compressor Products |
| Target Tire | Passenger car tire — 215/55R17 |
| Pressure Start | 25 psi |
| Pressure End | 35 psi |
| Number of Samples | 2 units (1# and 2#) |
| Runs per Sample | 10 consecutive runs |
| Total Data Points | 20 |
Test Equipment & Setup
| Parameter | Value |
|---|---|
| Device Under Test | ETENWOLF X6PRO Tire Inflator |
| Tire Specification | 215/55R17 passenger car tire |
| Starting Pressure | 25 psi |
| Target Pressure | 35 psi |
| Pressure Delta | 10 psi |
| Timing Method | Minutes and seconds (mm:ss) |
| Number of Test Units | 2 (designated 1# and 2#) |
| Runs per Unit | 10 |
| Total Runs | 20 |
Test Procedure
- Pre-test: Confirm tire is a 215/55R17 passenger car tire in serviceable condition.
- Pre-test: Deflate tire to starting pressure of 25 psi and verify with calibrated gauge.
- Pre-test: Connect ETENWOLF X6PRO inflator hose securely to tire valve stem.
- Procedure: Set X6PRO target pressure to 35 psi.
- Procedure: Start timing simultaneously with inflator activation (recorded in mm:ss format).
- Procedure: Stop timing when inflator auto-stops at 35 psi target pressure.
- Procedure: Record elapsed time for the run.
- Procedure: Repeat steps 2–7 for a total of 10 runs per unit.
- Procedure: Repeat full sequence for Unit 2#.
- Post-test: Compile all 20 run times and review for consistency.
- Acceptance Criteria: All runs must complete within a consistent and repeatable time window with no anomalies or failures to reach target pressure.
Test Data & Results
The table below presents all 20 inflation runs across both test units. Time is recorded in mm:ss format.
| Unit | Run No. | Time (mm:ss) | Unit | Run No. | Time (mm:ss) |
|---|---|---|---|---|---|
| 1# | 1 | 01:27 | 2# | 1 | 01:20 |
| 1# | 2 | 01:21 | 2# | 2 | 01:23 |
| 1# | 3 | 01:25 | 2# | 3 | 01:20 |
| 1# | 4 | 01:23 | 2# | 4 | 01:21 |
| 1# | 5 | 01:26 | 2# | 5 | 01:18 |
| 1# | 6 | 01:28 | 2# | 6 | 01:23 |
| 1# | 7 | 01:20 | 2# | 7 | 01:23 |
| 1# | 8 | 01:24 | 2# | 8 | 01:21 |
| 1# | 9 | 01:21 | 2# | 9 | 01:22 |
| 1# | 10 | 01:20 | 2# | 10 | 01:25 |
Observations: Unit 1# completed 10 runs with times ranging from 1 min 20 sec to 1 min 28 sec, giving a spread of 8 seconds. Unit 2# completed 10 runs ranging from 1 min 18 sec to 1 min 25 sec, a spread of 7 seconds. Both units demonstrate tight, repeatable performance. Unit 2# averaged marginally faster than Unit 1#. No run exceeded 1 min 30 sec and no anomalies or mid-run failures were observed across either unit.
Conclusion
| Item | Details |
|---|---|
| Product | ETENWOLF X6PRO Tire Inflator |
| Test Condition | 215/55R17 passenger car tire, 25 psi → 35 psi |
| Units Tested | 2 samples (1# and 2#), 10 runs each |
| Unit 1# Result | All 10 runs completed: 01:20 – 01:28 (min:sec) |
| Unit 2# Result | All 10 runs completed: 01:18 – 01:25 (min:sec) |
| Consistency | Both units show tight run-to-run repeatability (≤8 sec spread) |
| Verdict | PASS — Inflation efficiency is consistent and within acceptable performance range |
Document Information
| Role | Name |
|---|---|
| Author / Tester | Daniel Wright |
| Source File | X6pro-充气效率数据2026.2.10.xlsx |
| Sheet | 25-35psi打气时间 |
| Report Date | 2026-02-10 |
| Published Date | 2026-07-12 |
| Model | X6PRO |
| Product Line | Inflation Tools |
Frequently Asked Questions
How long does the ETENWOLF X6PRO take to inflate a 215/55R17 tire from 25 to 35 psi?
In controlled lab testing across 20 runs on two units, the X6PRO inflated a 215/55R17 passenger car tire from 25 psi to 35 psi in approximately 1 minute 18 seconds to 1 minute 28 seconds, with both units showing consistent, repeatable results.
Is the X6PRO inflation time consistent across multiple uses?
Yes. Both test units showed a run-to-run spread of 7–8 seconds across 10 consecutive runs each, demonstrating high repeatability. No anomalies or performance drops were recorded across any of the 20 test runs.
What tire size was used in the X6PRO inflation efficiency test?
The test used a 215/55R17 passenger car tire, which is a common mid-size sedan fitment. The pressure target was a 10 psi increase from 25 psi to 35 psi, a realistic top-up scenario for everyday driving conditions.
Which ETENWOLF X6PRO unit performed faster — Unit 1# or Unit 2#?
Unit 2# averaged marginally faster times, with its fastest run at 1 minute 18 seconds compared to Unit 1#’s fastest of 1 minute 20 seconds. Both units are within a narrow and consistent performance band, and the difference is negligible in practical use.