What does the WEEE directive compliance mean for the C2PRO?

WEEE compliance means the C2PRO has been independently assessed to meet the end-of-life recovery and recycling targets set by the WEEE Directive 2012/19/EU. It achieved an 88.18% recovery rate and a 78.50% reuse and recycling rate, both exceeding the EU minimum targets of 75% and 55% respectively.

What category does the C2PRO fall under in the WEEE Directive?

The C2PRO Wireless Portable Tire Pump is classified under Annex III, Category 5: Small Equipment of the WEEE Directive 2012/19/EU, carrying a minimum recovery target of 75% and a minimum reuse and recycling target of 55% from 15 August 2018 onward.

Which testing laboratory issued the WEEE report for the C2PRO?

The WEEE compliance test report (Report No. WTH25X11294799C) was issued by Waltek Testing Group (Shenzhen) Co., Ltd., an accredited third-party laboratory based in Shenzhen, Guangdong, China. The report was signed by Hugo. Chen and issued on 2025-11-19.

What materials in the C2PRO contribute most to its recyclability?

Metal parts represent the largest material fraction at 52.69% of total weight (208.29 g) and contribute 47.42% to the recovery rate and 42.15% to the reuse and recycling rate. Plastic parts are the second largest fraction at 38.23% (151.14 g), contributing 34.41% and 30.59% respectively.

WEEE Compliance Test Report – ETENWOLF C2PRO Wireless Portable Tire Pump (Report No. WTH25X11294799C)

Document Overview

Document Overview This article presents the official WEEE (Waste Electrical and Electronic Equipment) compliance test report issued for the ETENWOLF C2PRO Wireless Portable Tire Pump. The report was prepared and issued by Waltek Testing Group (Shenzhen) Co., Ltd., an accredited third-party testing laboratory located in…

Document type: Certification Report
Prepared by: Michelle Torres
Published: July 22, 2026
Last reviewed: July 22, 2026
Topics: European Union: CE / RoHS / REACH / WEEE

Document Overview

This article presents the official WEEE (Waste Electrical and Electronic Equipment) compliance test report issued for the ETENWOLF C2PRO Wireless Portable Tire Pump. The report was prepared and issued by Waltek Testing Group (Shenzhen) Co., Ltd., an accredited third-party testing laboratory located in Bao’an District, Shenzhen, Guangdong, China.

The assessment evaluates whether the product meets the material recovery, reuse, and recycling targets defined under the WEEE Directive 2012/19/EU, which governs the environmentally sound management of waste electrical and electronic equipment across EU member states.

Report Number: WTH25X11294799C
Document Type: WEEE Compliance Test Report
Issuing Laboratory: Waltek Testing Group (Shenzhen) Co., Ltd.
Date of Issue: 2025-11-19
Testing Period: 2025-11-11 to 2025-11-17
Date of Sample Receipt: 2025-11-11
Applicable Directive: WEEE Directive 2012/19/EU, Annex III – Category 5: Small Equipment
Overall Result: PASS

Product Information

The product assessed in this report is the C2PRO, a wireless portable tire pump designed and manufactured by Guangdong Bestek Technology Co., Ltd. The device is classified under WEEE Directive 2012/19/EU Annex III as Category 5: Small Equipment.

Field	Details
Sample Name	Wireless Portable Tire Pump
Model Number	C2pro
Product Weight	395.32 g
Applicant	Guangdong Bestek Technology Co., Ltd.
Applicant Address	No.1, North Gaopu 8th Road, Yuancheng Industrial Park, Heyuan City, Guangdong, P.R. China
Manufacturer	Guangdong Bestek Technology Co., Ltd.
Manufacturer Address	No.1, North Gaopu 8th Road, Yuancheng Industrial Park, Heyuan City, Guangdong, P.R. China
WEEE Category	Annex III – Category 5: Small Equipment
Sample Material	NA
Connection Technology	Screws: 13, Cells: 2, Glue: 0
Disassembly Time	15 minutes (performed on 2025-11-17)

The product includes a display screen, printed circuit boards, metal parts, plastic parts, and other miscellaneous components. The total assessed weight of 395.32 g covers the main product and all accessories.

Key Details

The core of the WEEE assessment is the material composition and the resulting reuse, recycling, and recovery rate calculation. The following table presents the full breakdown of materials and their respective recycling performance as tested under report WTH25X11294799C.

Materials and Recycling Information

Photo Ref.	Component / Material	Weight (g)	Weight (%)	Recovered (%)	Re-use & Recycled (%)
A38	Printed circuit board (surface > 10 cm²)	23.99	6.07	4.25	3.94
A39	Printed circuit board (surface < 10 cm²)	0.68	0.17	0.12	0.10
—	Display screen / Glass	—	—	—	—
A15–A30	Metal part	208.29	52.69	47.42	42.15
A1–A14	Plastic part	151.14	38.23	34.41	30.59
A31–A37	Other	11.22	2.84	1.99	1.70
Total	—	395.32	100	88.18	78.50

Note: Stickers, solder, paint, and printing materials are excluded from the assessment due to insignificant weight and difficulty of manual separation. Plastics containing brominated flame retardants are also excluded.

Recovery and Recycling Rate Summary

Target Type	Minimum Target (from 15 Aug 2018)	Actual Result	Compliance
Recovered (%)	75%	88.18%	OK
Re-use and Recycled (%)	55%	78.50%	OK

Selective Treatment Components (WEEE Directive Annex VII)

The following regulated materials and components were evaluated for selective treatment compliance in accordance with Article 8(2) and Annex VII of the WEEE Directive:

Printed circuit boards: PCB A38 (15.00 cm × 4.20 cm, 23.99 g) and PCB A39 (2.40 cm × 1.40 cm, 0.68 g)
Display screen (present in product)
Metal parts constituting 52.69% of total product weight
Plastic parts constituting 38.23% of total product weight

Disassembly Connection Techniques

Screws: 13
Cells (batteries): 2
Glue joints: 0
Total disassembly time: 15 minutes

Standards & Compliance

The C2PRO was assessed against the requirements of the following directives and regulatory frameworks:

Standard / Directive	Description	Result
WEEE Directive 2012/19/EU	Directive on waste electrical and electronic equipment; sets collection, recycling, and recovery targets	PASS
WEEE Directive 2012/19/EU – Annex III, Category 5	Classification as Small Equipment; minimum recovery target 75%, minimum reuse & recycling target 55%	PASS
WEEE Directive 2012/19/EU – Annex VII	Selective treatment requirements for specific materials and components	PASS
WEEE Directive 2012/19/EU – Annex II	Disassembly procedure requirements for treatment facilities	Applied
Council Directive 96/59/EC	Disposal of polychlorinated biphenyls (PCB) and polychlorinated terphenyls (PCT)	Referenced
Commission Directive 97/69/EC	Classification, packaging, and labelling of dangerous substances (refractory ceramic fibres)	Referenced

The disassembly procedure was conducted in accordance with Annex II of the WEEE Directive, using manual operation and standard disassembly tools to simulate treatment facility conditions. The objective was to separate components so that they can be reused, recycled, or recovered efficiently.

Rate calculation methodology applied in the report:

Reuse & Recycling Rate (%): Reuse & Recycling Weight ÷ Product Total Weight × 100
Recovery Rate (%): (Reuse & Recycling Weight + Energy Recovery Weight) ÷ Product Total Weight × 100

Validity & Certification Body

This test report was issued by Waltek Testing Group (Shenzhen) Co., Ltd., an accredited third-party testing and certification laboratory operating under the Waltek Testing Group.

Field	Details
Report Number	WTH25X11294799C
Issuing Laboratory	Waltek Testing Group (Shenzhen) Co., Ltd.
Laboratory Address	1/F., Room 101, Building 1, Hongwei Industrial Park, Liuxian 2nd Road, Block 70, Bao’an District, Shenzhen, Guangdong, China
Laboratory Website	http://www.waltek.com.cn
Telephone	+86-755-33663308
Fax	+86-755-33663309
Email	[email protected]
Signed By	Hugo. Chen, on behalf of Waltek Testing Group (Shenzhen) Co., Ltd.
Date of Issue	2025-11-19
Testing Period	2025-11-11 to 2025-11-17
Date of Sample Receipt	2025-11-11

Important validity conditions:

The results in this report apply exclusively to the specific sample(s) tested.
The report may not be reproduced in part without prior written permission from Waltek Testing Group (Shenzhen) Co., Ltd.
The report is invalid without the specific stamp of the test institute and the signatures of both the compiler and approver.
Applicant-provided information regarding sample identity and address has not been independently verified by Waltek.
If the report does not bear the accreditation recognized seal, it is limited to use for scientific research, education, and internal quality control, and may not be used to issue supporting data to the public.

Frequently Asked Questions

What does the WEEE directive compliance mean for the C2PRO?: WEEE compliance means the C2PRO has been independently assessed to meet the end-of-life recovery and recycling targets set by the WEEE Directive 2012/19/EU. Specifically, it achieved an 88.18% recovery rate and a 78.50% reuse and recycling rate, both exceeding the EU minimum targets of 75% and 55% respectively. This confirms that at the end of its operational life, the majority of the product’s materials can be responsibly recovered or recycled.
What category does the C2PRO fall under in the WEEE Directive?: The C2PRO Wireless Portable Tire Pump is classified under Annex III, Category 5: Small Equipment of the WEEE Directive 2012/19/EU. This category includes small household and portable electronic devices, and carries a minimum recovery target of 75% and a minimum reuse and recycling target of 55% from 15 August 2018 onward.
Which testing laboratory issued the WEEE report for the C2PRO?: The WEEE compliance test report (Report No. WTH25X11294799C) was issued by Waltek Testing Group (Shenzhen) Co., Ltd., an accredited third-party laboratory based in Shenzhen, Guangdong, China. The report was signed by Hugo. Chen on behalf of the laboratory and issued on 2025-11-19.
What materials in the C2PRO contribute most to its recyclability?: Metal parts represent the largest material fraction at 52.69% of total weight (208.29 g) and contribute 47.42% to the recovery rate and 42.15% to the reuse and recycling rate. Plastic parts are the second largest fraction at 38.23% (151.14 g), contributing 34.41% and 30.59% respectively. Printed circuit boards and other components make up the remainder of the assessed mass.