What does the RoHS PASS result mean for the V3 Air Inflator?

A PASS result means that all 84 tested components of the V3 Air Inflator contain restricted hazardous substances — including lead, mercury, cadmium, hexavalent chromium, PBBs, PBDEs, and the four phthalates — at levels below the maximum concentration limits set by EU RoHS Directive 2011/65/EU and its amendment (EU) 2015/863. The product is legally compliant for sale in the European Union and other RoHS-adopting markets.

Which hazardous substances were tested under this report?

The report covers the 10 substances restricted under the amended EU RoHS Directive: Lead (Pb), Mercury (Hg), Cadmium (Cd), Hexavalent Chromium (Cr6+), Polybrominated Biphenyls (PBBs), Polybrominated Diphenyl Ethers (PBDEs), and four phthalates — DEHP, BBP, DBP, and DIBP. Each substance was tested using internationally recognised IEC 62321-series methods.

Why were some components flagged as Inconclusive (IN) in XRF screening?

XRF screening is a non-destructive primary screening technique. When a result is Inconclusive (IN), the laboratory performs confirmatory chemical analysis. For every IN result in this report, follow-up testing confirmed either Negative or Not Detected (ND) for the relevant restricted substance. All IN flags were resolved as compliant.

Is this RoHS report sufficient for CE marking of the V3 Air Inflator?

RoHS compliance is one component of CE marking requirements. This report demonstrates conformity with RoHS Directive 2011/65/EU for the V3 Air Inflator. CE marking may additionally require conformity assessments under other applicable directives such as the Low Voltage Directive or Machinery Directive. Consult your regulatory advisor for complete CE marking documentation requirements.

RoHS Compliance Test Report – ETENWOLF V3 Air Inflator (Report No. WTH25X05129148C)

Document Overview

Document Overview This page presents the official RoHS test report issued for the ETENWOLF V3 Air Inflator. The report was prepared by Waltek Testing Group (Shenzhen) Co., Ltd., an accredited third-party testing laboratory, and carries Report Number WTH25X05129148C. The test was conducted in accordance with…

Document type: Certification Report
Prepared by: Michelle Torres
Published: July 22, 2026
Last reviewed: July 22, 2026
Topics: European Union: CE / RoHS / REACH / WEEE

Document Overview

This page presents the official RoHS test report issued for the ETENWOLF V3 Air Inflator. The report was prepared by Waltek Testing Group (Shenzhen) Co., Ltd., an accredited third-party testing laboratory, and carries Report Number WTH25X05129148C.

The test was conducted in accordance with the EU RoHS Directive 2011/65/EU and its amending regulation (EU) 2015/863, which restricts the use of 10 hazardous substances in electrical and electronic equipment placed on the European market.

Report Number: WTH25X05129148C
Document Type: RoHS Test Report
Issuing Body: Waltek Testing Group (Shenzhen) Co., Ltd.
Date of Issue: 2025-06-17
Test Conclusion: PASS
Applicable Directive: EU RoHS Directive 2011/65/EU and amendment (EU) 2015/863
Scope: Determination of 10 restricted hazardous substances in all submitted sample components

Product Information

The tested product is the V3 Air Inflator, an electric portable inflation tool manufactured by Guangdong Bestek Technology Co., LTD and distributed under the ETENWOLF brand. The product is designed for inflating tires, sports equipment, and other inflatable items.

Field	Details
Sample Name	Air Inflator
Model Number	V3
Reference Model	NA
Brand	NA (distributed by ETENWOLF)
Applicant	Guangdong Bestek Technology Co., LTD
Manufacturer	Guangdong Bestek Technology Co., LTD
Manufacturer Address	No.1, North Gaopu 8th Road, Yuancheng Industrial Park, Heyuan City, Guangdong, P.R. China
Date of Sample Receipt	2025-05-23 & 2025-06-10 & 2025-06-13
Testing Period	2025-05-23 ~ 2025-06-04 & 2025-06-10 ~ 2025-06-12 & 2025-06-13 ~ 2025-06-15

Key Details

The V3 Air Inflator was disassembled into 84 individual component parts, each tested for the presence of RoHS-restricted substances. All components returned results below detection limits (BL) or were confirmed as Not Detected (ND) through follow-up chemical analysis where flagged as Inconclusive (IN) by XRF screening. The overall test conclusion is PASS.

Below is a representative summary of tested parts and their results for the primary restricted substances: Lead (Pb), Cadmium (Cd), Mercury (Hg), Total Chromium (Cr), and Bromine (Br) via XRF, with chemical confirmation where required.

Part No.	Part Description	XRF Result	Chemical Confirmation
1	Orange plastic shell	All BL	NA
5–10	Black rubber / Black rubber ring	All BL	NA
14	Silvery metal spring	Cr: IN	Cr6+: Negative
17	Black cladding metal screw	Cr: IN	Cr6+: ND
24	Dark metal gear	Cr: IN	Cr6+: Negative
25	Silvery metal axle	Cr: IN	Cr6+: Negative
40	Silvery metal cover	Cr: IN	Cr6+: Negative
50	Black cladding PCB board	Br: IN	PBBs: ND / PBDEs: ND
62	Silvery square metal body (switch)	Cr: IN	Cr6+: Negative
64	Black cladding PCB board (whole)	Br: IN	PBBs: ND / PBDEs: ND
74	Green cladding PCB board (whole)	All BL	NA
79	Gray solid material body (Inductance)	Cr: IN	Cr6+: ND

In every case where XRF screening produced an Inconclusive (IN) result, follow-up chemical analysis confirmed no hexavalent chromium (Cr6+), no polybrominated biphenyls (PBBs), and no polybrominated diphenyl ethers (PBDEs) in excess of permissible limits. All remaining parts tested Below Limit (BL) for all restricted substances.

Standards & Compliance

The testing program applied a suite of internationally recognised IEC test methods to characterise each restricted substance category. The following standards were used:

Standard	Scope	Analytical Method
IEC 62321-3-1:2013	Screening – Pb, Hg, Cd, total Cr, total Br	X-Ray Fluorescence Spectrometry (XRF)
IEC 62321-4:2013+AMD1:2017 CSV	Mercury (Hg)	ICP-OES
IEC 62321-5:2013	Lead (Pb) and Cadmium (Cd)	ICP-OES
IEC 62321-7-2:2017 and/or IEC 62321-7-1:2015	Hexavalent Chromium (Cr6+)	UV-Vis Spectrophotometry
IEC 62321-6:2015	PBBs and PBDEs	GC-MS
IEC 62321-8:2017	Phthalates (DEHP, BBP, DBP, DIBP)	GC-MS

The applicable regulatory framework is the EU RoHS Directive 2011/65/EU, as amended by (EU) 2015/863, which extended restricted phthalates (DEHP, BBP, DBP, DIBP) to the full list of 10 restricted substances effective July 2019 for most product categories.

Validity & Certification Body

The test report was issued on 2025-06-17 by Waltek Testing Group (Shenzhen) Co., Ltd., a globally recognised third-party testing, inspection, and certification laboratory. RoHS test reports of this type are valid as long as the product design, materials, and supply chain remain unchanged. Any material substitution or design revision would require re-testing to maintain compliance status.

Field	Details
Laboratory	Waltek Testing Group (Shenzhen) Co., Ltd.
Laboratory Address	1/F., Room 101, Building 1, Hongwei Industrial Park, Liuxian 2nd Road, Block 70 Bao’an District, Shenzhen, Guangdong, China
Laboratory Website	http://www.waltek.com.cn
Telephone	+86-755-33663308
Fax	+86-755-33663309
Email	[email protected]
Report Signed By	Hugo Chen
Date of Issue	2025-06-17
Report Number	WTH25X05129148C
Validity Note	Valid while product materials and design remain unchanged

Frequently Asked Questions

Q: What does the RoHS PASS result mean for the V3 Air Inflator?: A PASS result means that all 84 tested components of the V3 Air Inflator contain restricted hazardous substances — including lead, mercury, cadmium, hexavalent chromium, PBBs, PBDEs, and the four phthalates — at levels below the maximum concentration limits set by EU RoHS Directive 2011/65/EU and its amendment (EU) 2015/863. The product is legally compliant for sale in the European Union and other RoHS-adopting markets.
Q: Which hazardous substances were tested under this report?: The report covers the 10 substances restricted under the amended EU RoHS Directive: Lead (Pb), Mercury (Hg), Cadmium (Cd), Hexavalent Chromium (Cr6+), Polybrominated Biphenyls (PBBs), Polybrominated Diphenyl Ethers (PBDEs), and four phthalates — DEHP, BBP, DBP, and DIBP. Each substance was tested using internationally recognised IEC 62321-series methods.
Q: Why were some components flagged as Inconclusive (IN) in XRF screening?: XRF screening is a non-destructive primary screening technique. When a result is Inconclusive (IN) — typically due to chromium or bromine readings near detection thresholds — the laboratory performs confirmatory chemical analysis. For every IN result in this report, follow-up testing confirmed either Negative or Not Detected (ND) for the relevant restricted substance. All IN flags were resolved as compliant.
Q: Is this RoHS report sufficient for CE marking of the V3 Air Inflator?: RoHS compliance is one component of the CE marking requirements. This report, issued by accredited laboratory Waltek Testing Group, demonstrates conformity with the RoHS Directive 2011/65/EU for the V3 Air Inflator. CE marking may additionally require conformity assessments under other applicable directives such as the Low Voltage Directive or the Machinery Directive depending on the product’s full specification and intended market. Consult your regulatory advisor for complete CE marking documentation requirements.