What does the drop test report WTH25H05125168P confirm about the ETENWOLF S6?

Report WTH25H05125168P confirms that the ETENWOLF S6 inflator pump successfully passed a 10-sequence drop test at 1000 mm height covering all critical corners, edges, and faces of the package. After all drops, the unit showed no physical damage, no deformation, no loosening, and all functions — startup and charging — operated normally.

Which standard was used for the drop test, and what does it cover?

The test was conducted according to GB/T 4857.5-1992, the Chinese national standard for package drop testing. It simulates the mechanical shocks a packaged product may experience during transportation and distribution by dropping it from a defined height onto a hard surface across multiple orientations.

Who conducted the drop test for the S6 inflator pump?

The test was conducted by Waltek Testing Group HCT (Shenzhen) Co., Ltd., an established testing laboratory based in Shenzhen, Guangdong, China. The report was tested by Daymon (许东豪), inspected by Jeson Qi (戚照刚), and approved by Sem Huang (黄庆盛).

Is this drop test report sufficient for customs, retail, or compliance submissions?

This report was issued without a CMA (China Metrology Accreditation) logo, which means it is primarily intended for the client's internal quality control, product development, and scientific reference purposes. For regulatory submissions or retail compliance requirements that specifically require CMA- or CNAS-accredited results, please contact the manufacturer or laboratory for an appropriately accredited report version.

ETENWOLF S6 Inflator Pump Drop Test Report — WTH25H05125168P

Document Overview

Document Overview This page presents the official drop test report issued by Waltek Testing Group HCT (Shenzhen) Co., Ltd. (深圳市沃特虹彩检测技术有限公司) for the ETENWOLF S6 cordless inflator pump. The report documents a structured package drop test conducted in accordance with Chinese national standard GB/T 4857.5-1992 to…

Document type: Certification Report
Prepared by: Michelle Torres
Published: July 22, 2026
Last reviewed: July 25, 2026
Topics: Mechanical Reliability

Document Overview

This page presents the official drop test report issued by Waltek Testing Group HCT (Shenzhen) Co., Ltd. (深圳市沃特虹彩检测技术有限公司) for the ETENWOLF S6 cordless inflator pump. The report documents a structured package drop test conducted in accordance with Chinese national standard GB/T 4857.5-1992 to evaluate the product’s ability to withstand mechanical shock during transportation and handling.

Report Number: WTH25H05125168P
Document Type: Drop Test Report (跌落测试报告)
Issuing Laboratory: Waltek Testing Group HCT (Shenzhen) Co., Ltd.
Date of Issue: 2025-05-27
Testing Period: 2025-05-19 to 2025-05-25
Date of Sample Receipt: 2025-05-16
Scope: Mechanical drop durability of the packaged inflator pump unit across 10 defined drop orientations at a height of 1000 mm

Product Information

The product evaluated in this report is the ETENWOLF Vortex S6 Heavy-Duty Cordless Inflator, a portable battery-powered inflation device designed for heavy-duty use with tires, inflatables, and other applications.

Field	Detail
Product Name	Inflator Pump (充气泵)
Model Number	S6
Sample ID Used in Test	S-01
Sample Weight	3.90 kg
Applicant	Guangdong Bestek Technology Co., LTD
Applicant Address	No.1, North Gaopu 8th Road, Yuancheng Industrial Park, Heyuan City, Guangdong, P.R. China
Manufacturer	Guangdong Bestek Technology Co., LTD
Manufacturer Address	No.1, North Gaopu 8th Road, Yuancheng Industrial Park, Heyuan City, Guangdong, P.R. China

Key Details

The drop test was carried out using a calibrated package drop testing machine (Model DT-325, Equipment No. WTHP1300A1-001, calibrated 2025-01-02, valid to 2026-01-01) and a calibrated electronic scale (Model XK3116, Equipment No. WTHP1180A1-001, calibrated 2024-07-31, valid to 2025-07-30). Ambient conditions during testing were 24.8 °C and 53.0% RH.

The test followed the sequential drop method defined in GB/T 4857.5-1992, covering all major corners, edges, and faces of the packaged product at a uniform drop height of 1000 mm. The full sequence is detailed below:

Sequence	Drop Position	Drop Height	Sample Weight
1	Corner 2-3-5	1000 mm	3.90 kg
2	Edge 2-5	1000 mm	3.90 kg
3	Edge 3-5	1000 mm	3.90 kg
4	Edge 2-3	1000 mm	3.90 kg
5	Face 5	1000 mm	3.90 kg
6	Face 6	1000 mm	3.90 kg
7	Face 2	1000 mm	3.90 kg
8	Face 4	1000 mm	3.90 kg
9	Face 3	1000 mm	3.90 kg
10	Face 1	1000 mm	3.90 kg

Test Result (Visual Inspection — Sample S-01): After completing all 10 drop sequences, the internal sample showed no damage, no deformation, no shedding, no loosening, and no cracking. Post-test functional verification confirmed that the startup function operated normally and the charging function operated normally. The ETENWOLF S6 passed all drop test requirements.

Standards & Compliance

The drop test was conducted in strict accordance with the following national standard:

Standard	Title	Scope
GB/T 4857.5-1992	Packaging — Basic Tests for Transport Packages — Drop Test Method	Defines the method for drop testing packaged products to simulate conditions encountered during distribution and transportation

The standard specifies that a test is passed when the measured outcome meets or does not exceed the defined limit, regardless of measurement uncertainty. If a measured value exceeds the limit, the test is considered failed. All instruments used in this test are calibrated and traceable to national or international standards; further traceability information is available from the laboratory on request.

This report was prepared under the laboratory’s internal test report form reference TRFCHEN-SE-001-V01. Note that results in reports without a CMA logo are intended for the client’s internal quality control, product research and development, and scientific reference purposes, and do not constitute public proof of conformity.

Validity & Certification Body

The report was issued on 2025-05-27 and is valid as issued. Any dispute regarding the contents of this report must be submitted to the testing laboratory within 15 calendar days of receipt. Partial reproduction of this report is prohibited without written approval from Waltek Testing Group HCT (Shenzhen) Co., Ltd.

Field	Detail
Laboratory Name	Waltek Testing Group HCT (Shenzhen) Co., Ltd. (深圳市沃特虹彩检测技术有限公司)
Laboratory Website	http://www.hct-test.com
Laboratory Address	Building B, Tianji Industrial Park, 1/F, 2/F & 3/F, No.30-9, Laiyin Road, Xinsheng Community, Longgang Subdistrict, Longgang District, Shenzhen, Guangdong, China
Telephone	+86-0755-84616666
Email	[email protected]
Tested by	许东豪 / Daymon
Inspected by	戚照刚 / Jeson Qi
Approved by	黄庆盛 / Sem Huang
Report Form No.	TRFCHEN-SE-001-V01
Report Pages	7 pages

Frequently Asked Questions

What does the drop test report WTH25H05125168P confirm about the ETENWOLF S6?: Report WTH25H05125168P confirms that the ETENWOLF S6 inflator pump successfully passed a 10-sequence drop test at 1000 mm height covering all critical corners, edges, and faces of the package. After all drops, the unit showed no physical damage, no deformation, no loosening, and all functions — startup and charging — operated normally.
Which standard was used for the drop test, and what does it cover?: The test was conducted according to GB/T 4857.5-1992, the Chinese national standard for package drop testing. It simulates the mechanical shocks a packaged product may experience during transportation and distribution by dropping it from a defined height onto a hard surface across multiple orientations.
Who conducted the drop test for the S6 inflator pump?: The test was conducted by Waltek Testing Group HCT (Shenzhen) Co., Ltd., an established testing laboratory based in Shenzhen, Guangdong, China. The report was tested by Daymon (许东豪), inspected by Jeson Qi (戚照刚), and approved by Sem Huang (黄庆盛).
Is this drop test report sufficient for customs, retail, or compliance submissions?: This report was issued without a CMA (China Metrology Accreditation) logo, which means it is primarily intended for the client’s internal quality control, product development, and scientific reference purposes. For regulatory submissions, customs declarations, or retail compliance requirements that specifically require CMA- or CNAS-accredited results, please contact the manufacturer or laboratory for an appropriately accredited report version.