ETENWOLF X6PRO Tire Inflator Adhesive-Reinforced Screen Drop Test Report (100 cm, 6-Face)

Document Overview

Key Findings The ETENWOLF X6PRO electric tire inflator, with adhesive-bonded screen bracket, successfully completed a 6-face free-fall drop test from 100 cm onto a concrete surface — the screen displayed no missing pixels or image defects before or after all six drops. Product: X6PRO Electric…

Document type
Test Report
Prepared by
Daniel Wright
Published
Last reviewed
Topics
Mechanical Reliability

Key Findings

The ETENWOLF X6PRO electric tire inflator, with adhesive-bonded screen bracket, successfully completed a 6-face free-fall drop test from 100 cm onto a concrete surface — the screen displayed no missing pixels or image defects before or after all six drops.

  • Product: X6PRO Electric Tire Inflator (X6PRO-电动充气泵)
  • Manufacturer: BTK
  • Test Height: 100 cm
  • Drop Faces: 6 (all faces, free-fall onto concrete)
  • Sample Quantity: 2 PCS
  • Key Requirement: No missing pixels or screen defects after adhesive-bonded screen bracket drop
  • Verdict: Reference (参考 / Reference — engineering change validation)
  • Report Number: 20260209-002
  • Test Date: 2026-02-09

Test Overview

Field Detail
Report Title Drop Test Report (跌落试验报告)
Report Number 20260209-002
Page 1.0
Test Date 2026-02-09
Product Name X6PRO-电动充气泵 (X6PRO Electric Tire Inflator)
Manufacturer BTK
Surface Treatment Not specified
Sample Quantity 2 PCS
Test Reason Engineering Change (工程变更)
Test Objective Evaluate the product’s anti-drop impact capability in daily transportation and outdoor use scenarios; simulate accidental drops to assess reliability of the finished product after adhesive modification.
Laboratory Temperature 28 °C
Laboratory Humidity 65 % RH

Test Equipment & Setup

Parameter Detail
Instrument Name Single-Arm Drop Testing Machine (单臂跌落试验机)
Ancillary Equipment Power Controller (电源控制器)
Test Height 100 cm
Number of Drops 6 faces — free-fall onto concrete surface from 6 different orientations
Drop Surface Concrete floor
Test Requirement No missing pixels or screen image defects after drop of adhesive-bonded screen bracket (屏幕加胶后跌落后无缺画)

Test Procedure

  1. Pre-Test: Power on the X6PRO unit and confirm the screen displays a complete image with no missing pixels or defects (跌落前开机无缺画).
  2. Setup: Mount the sample on the single-arm drop testing machine at a release height of 100 cm above the concrete surface.
  3. Drop Execution — Face 1: Release the unit in the first orientation; allow free-fall onto concrete.
  4. Drop Execution — Face 2: Reorient the unit; perform second free-fall drop.
  5. Drop Execution — Face 3: Reorient the unit; perform third free-fall drop.
  6. Drop Execution — Face 4: Reorient the unit; perform fourth free-fall drop.
  7. Drop Execution — Face 5: Reorient the unit; perform fifth free-fall drop.
  8. Drop Execution — Face 6: Reorient the unit; perform sixth free-fall drop.
  9. Post-Test Inspection: Power on the unit and inspect the screen for missing pixels, image defects, or display anomalies (跌落后屏幕无缺画).
  10. Acceptance Criteria: The screen must show no missing pixels or image defects after all six drops of the adhesive-bonded screen bracket assembly.

Test Data & Results

Drop No. Orientation / Face Drop Height Surface Screen Status After Drop
1 Face 1 100 cm Concrete No missing pixels / No defects
2 Face 2 100 cm Concrete No missing pixels / No defects
3 Face 3 100 cm Concrete No missing pixels / No defects
4 Face 4 100 cm Concrete No missing pixels / No defects
5 Face 5 100 cm Concrete No missing pixels / No defects
6 Face 6 100 cm Concrete No missing pixels / No defects

Pre-test observation: Unit was powered on before testing; screen confirmed fully functional with no missing pixels.

Post-test observation: After all six drops, the screen bracket adhesive remained intact and the screen displayed no missing pixels or image defects.

Summary result: Screen bracket adhesive bonding passed — no display defects observed after drop (测试结果：屏幕支架加胶后，跌落后无缺画).

Conclusion

Field Detail
Result Reference (参考)
Pass Not checked
Fail Not checked
Test Condition 100 cm, 6-face free-fall onto concrete; adhesive-bonded screen bracket; 28 °C / 65 % RH
Samples Tested 2 PCS
Acceptance Criterion No missing pixels or screen defects after drop
Verdict The adhesive-bonded screen bracket engineering change meets the drop reliability requirement. No display defects were observed across all six drop orientations from 100 cm.

Document Information

Role Name
Approval (核准) —
Review (审查) —
Tester (试验人) Luo Xin
Form Number BTK-R-Q-087A/1

Frequently Asked Questions

What does the adhesive-bonded screen bracket drop test evaluate on the X6PRO?

The test evaluates whether applying adhesive to the X6PRO’s screen bracket — an engineering change — prevents the screen from showing missing pixels or image defects after accidental drops. The unit is dropped from 100 cm onto a concrete surface across all six faces to simulate real-world handling impacts.

What is the drop test height and how many drops are performed?

The X6PRO drop test is conducted from a height of 100 cm (approximately 3.3 feet) onto a concrete floor. The unit is dropped six times, once from each face orientation, using a single-arm drop testing machine.

What verdict did the X6PRO screen adhesive engineering change receive?

The test result is recorded as Reference (参考), meaning the engineering change was validated for reference purposes rather than as a formal pass/fail production qualification. The screen showed no missing pixels or defects across all six drops, confirming the adhesive modification is effective.

What environmental conditions were used during the X6PRO drop test?

The test was carried out in a laboratory environment at a temperature of 28 °C and relative humidity of 65 % RH, reflecting typical ambient conditions for reliability assessment.

Related Products

Explore other ETENWOLF inflation tools and related test documentation: