Document Overview
Key Findings The ETENWOLF Vortex S6 cordless inflator passed a 1-hour random vibration test conducted to ISTA-2A standards, with all three samples demonstrating normal power-on operation, intact appearance, functional button response, and accurate inflation readings after the full test duration. Test Standard: ISTA-2A Test Mode:…
- Document type
- Test Report
- Prepared by
- Daniel Wright
- Published
- Last reviewed
- Topics
- Mechanical Reliability
Key Findings
The ETENWOLF Vortex S6 cordless inflator passed a 1-hour random vibration test conducted to ISTA-2A standards, with all three samples demonstrating normal power-on operation, intact appearance, functional button response, and accurate inflation readings after the full test duration.
- Test Standard: ISTA-2A
- Test Mode: Random vibration, axes X / Y / Z
- Duration: 1 hour
- Frequency: 4 Hz
- Test Speed (CMP): 240 G
- Vibration Amplitude: 25.4 mm
- Sample Quantity: 3 pcs
- Overall Verdict: PASS
Test Overview
| Field | Detail |
|---|---|
| Test Type | Transport Vibration Test |
| Test Standard | ISTA-2A |
| Report Number | 2025052601 |
| Page | 1 |
| Date | 2025-05-26 |
| Product Name | ETENWOLF Vortex S6 Cordless Inflator (S6-充气泵) |
| Manufacturer | BTK |
| Surface Treatment | / |
| Sample Quantity | 3 PCS |
| Test Reason | New Product |
| Test Objective | To verify the resistance of the sample in transportation and use environment. |
| Laboratory Temperature | 22 °C |
| Laboratory Humidity | 55% RH |
Test Equipment & Setup
| Parameter | Value |
|---|---|
| Instrument Name | Vibration Testing Machine |
| Test Mode | Random Mode |
| Test Duration | 1 H |
| Random Directions | X, Y, Z |
| Vibration Frequency | 4 Hz |
| Test Speed (CMP) | 240 G |
| Vibration Amplitude | 25.4 mm |
Test Procedure
- Pre-Test Inspection: Record the appearance of all three S6 samples, verify normal power-on and button functionality, and confirm inflation accuracy readings are within specification before mounting.
- Sample Placement: Position samples on the vibration table in the configuration shown in the vibration-placement photograph (振动摆放).
- Control Configuration: Connect the vibration controller and verify the control chart (振动控制图) matches the ISTA-2A random profile at 4 Hz / 240 G CMP / 25.4 mm amplitude.
- Vibration Execution: Run the random vibration sequence for 1 hour, cycling through X, Y, and Z axes.
- Post-Test Inspection: Power on each sample and inspect for: (a) normal startup with no faults; (b) intact appearance and no physical damage; (c) all buttons functioning correctly; (d) inflation accuracy within accepted tolerance.
- Acceptance Criterion: All samples must power on normally and exhibit no functional failures after the test. Any failure results in a Fail verdict for the entire lot.
Test Data & Results
| Check Item | Requirement | Post-Test Observation | Result |
|---|---|---|---|
| Power-On & Operation | Normal startup, no abnormality | All 3 samples powered on normally; no faults observed | PASS |
| Appearance | No damage, no abnormal deformation | Post-transport appearance showed no abnormality (运输后外观功能无异常) | PASS |
| Button Functionality | All buttons respond correctly | Button functions normal (按健功能无异常) | PASS |
| Charging Function | Charges normally | Charging normal (充电正常) | PASS |
| Inflation Accuracy | Within specified tolerance | Inflation accuracy normal (充气精度正常) | PASS |
Summary Observation: After the 1-hour vibration test, all S6 inflator samples powered on and operated without abnormality. Appearance and button functions showed no issues. Inflation accuracy test result: OK. (S6充气泵样品经过1小时振动测试后,开机工作无异常,外观按健功能无异常,充气精度测试OK)
Conclusion
| Field | Detail |
|---|---|
| Verdict | PASS |
| Standard Applied | ISTA-2A |
| Test Conditions | Random vibration, 4 Hz, 240 G CMP, 25.4 mm amplitude, 1 H, axes X/Y/Z, 22 °C / 55% RH |
| Samples Tested | 3 PCS |
| Judgment Basis | Post-test: normal power-on, no functional failure, inflation accuracy OK |
| Fail / Reference | Neither — all samples passed |
Document Information
| Role | Name (Pinyin) |
|---|---|
| Approval (核准) | Mai Shaoqiang |
| Review (审查) | Zhang Ronggui |
| Tester (试验人) | Li Guanghua |
| Field | Value |
|---|---|
| Form Number | BTK-R-Q-087A/1 |
| Report Number | 2025052601 |
| Date | 2025-05-26 |
Frequently Asked Questions
What vibration test standard was used for the ETENWOLF Vortex S6 inflator?
The S6 inflator was tested to ISTA-2A, a transport simulation standard that evaluates a product’s ability to withstand the vibration stresses encountered during shipping and distribution.
What were the key vibration test parameters for the S6?
The test ran in random mode for 1 hour across X, Y, and Z axes at a vibration frequency of 4 Hz, a test speed of 240 G CMP, and a vibration amplitude of 25.4 mm. The lab environment was maintained at 22 °C and 55% RH.
Did the ETENWOLF Vortex S6 pass the transport vibration test?
Yes. All three S6 samples passed. After the 1-hour random vibration sequence, every unit powered on normally, showed no appearance damage, had fully functional buttons, charged correctly, and maintained accurate inflation readings.
How many samples of the S6 were tested in the vibration study?
Three production samples (3 PCS) of the S6 cordless inflator were subjected to the full ISTA-2A vibration protocol. All three met the acceptance criteria with no functional failures recorded.