What does it mean that the ETENWOLF CL5 passed RoHS testing?

A RoHS pass means that all 10 substances restricted under EU Directive 2011/65/EU and its amendment (EU) 2015/863 — including lead, mercury, cadmium, hexavalent chromium, PBBs, PBDEs, and four phthalates — were found at or below the maximum permitted concentration values in every tested component of the CL5. This allows the product to be legally placed on the EU market.

Which laboratory conducted the testing, and is it accredited?

Testing was performed by Waltek Testing Group (Shenzhen) Co., Ltd., an internationally recognised third-party testing laboratory based in Shenzhen, China. Report number WTH26X01027993C was issued on 2026-02-27 and signed by Hugo Chen on behalf of the laboratory.

How many individual components were tested in the CL5?

At least 81 individually identified components were tested, covering the full range of materials present in the CL5 — including plastics, rubbers, metals, PCB boards, solder joints, LEDs, SMD components, wire jackets, and USB connectors. All components returned compliant results.

What is the difference between a BL result and an IN result in the test table?

BL (Below Limit) means XRF screening detected the substance at a level below the threshold requiring further investigation — no chemical confirmation was needed. IN (Inconclusive) means XRF detected a signal that could not rule out a restricted substance, so chemical confirmation testing (ICP-OES, UV-Vis, or GC-MS) was performed. All IN-flagged components passed their confirmatory chemical tests, with results such as Cr6+: Negative and PBBs/PBDEs: Not Detected.

RoHS Compliance Test Report – ETENWOLF CL5 2-in-1 Camping Flashlight | Report WTH26X01027993C

Document Overview

Document Overview This page presents the findings of a formal RoHS test report issued by Waltek Testing Group (Shenzhen) Co., Ltd., an accredited third-party testing laboratory. The report covers restricted hazardous substance testing performed on the ETENWOLF CL5 2-in-1 Camping Flashlight to verify conformity with…

Document type: Certification Report
Prepared by: Michelle Torres
Published: July 21, 2026
Last reviewed: July 21, 2026
Topics: Lighting Gear

Document Overview

This page presents the findings of a formal RoHS test report issued by Waltek Testing Group (Shenzhen) Co., Ltd., an accredited third-party testing laboratory. The report covers restricted hazardous substance testing performed on the ETENWOLF CL5 2-in-1 Camping Flashlight to verify conformity with the European Union RoHS Directive.

Field	Detail
Report Number	WTH26X01027993C
Document Type	RoHS Test Report
Issuing Laboratory	Waltek Testing Group (Shenzhen) Co., Ltd.
Applicable Directive	EU RoHS Directive 2011/65/EU & Amendment (EU) 2015/863
Date of Sample Receipt	2026-01-31
Testing Period	2026-01-31 to 2026-02-11
Date of Issue	2026-02-27
Overall Conclusion	Pass

The test conclusion confirms that all 10 restricted substances regulated under EU RoHS Directive 2011/65/EU and its amendment (EU) 2015/863 were found to comply with the required maximum concentration limits in all tested sample components.

Product Information

The sample submitted for testing is manufactured and supplied by Guangdong Bestek Technology Co., LTD, the applicant of record for this report. The product is marketed under the ETENWOLF brand.

Field	Detail
Sample Name	2-in-1 Camping Flashlight
Model Number	CL5
Reference Model No.	NA
Brand	NA (marketed as ETENWOLF)
Applicant	Guangdong Bestek Technology Co., LTD
Applicant Address	No.1, North Gaopu 8th Road, Yuancheng Industrial Park, Heyuan City, Guangdong, P.R.China
Manufacturer	Guangdong Bestek Technology Co., LTD
Manufacturer Address	No.1, North Gaopu 8th Road, Yuancheng Industrial Park, Heyuan City, Guangdong, P.R.China

The ETENWOLF CL5 is a rechargeable 2-in-1 camping lantern and flashlight designed for outdoor use. Its construction incorporates a wide range of material types — including various plastics, rubber components, metal hardware, PCB assemblies, LEDs, wire jackets, SMD components, and USB connectors (Type-A and Type-C) — all of which were individually sampled and tested for restricted substance content.

Key Details

Testing was conducted across 81 individually identified component parts. All components returned a Below Limit (BL) result on XRF screening for lead (Pb), cadmium (Cd), mercury (Hg), chromium (Cr), and bromine (Br) where applicable. Components requiring chemical confirmation testing also passed. The following table summarises representative results across the major material categories tested.

Part No.	Part Description	XRF Screen	Pb (mg/kg)	Cd (mg/kg)	Hg (mg/kg)	Cr	Br / PBBs / PBDEs
1–4	Transparent and white plastic	BL	BL	BL	BL	BL	NA
5, 7, 13–16	Black cladding metal, silvery metal, metal screws	BL	BL	BL	BL	BL	NA
8–12	Orange, white, and transparent rubber	BL	BL	BL	BL	BL	NA
18, 37, 39, 65, 78	Solder (multiple locations)	BL	BL	BL	BL	NA	NA
20–34, 72–73, 75	Plastic wire jackets (red, black, green, blue, gray)	BL	BL	BL	BL	BL	NA
35–36, 41–42, 67	Yellow, white, and red LEDs	BL	BL	BL	BL	BL	NA
40	White cladding PCB board	BL	BL	BL	BL	IN	PBBs: ND / PBDEs: ND
45	Beige plastic	BL	BL	BL	BL	IN	PBBs: ND / PBDEs: ND
49	Silvery metal sheet (switch)	BL	BL	BL	IN	NA	Cr6+: Negative
55	Silvery metal shell (switch)	BL	BL	BL	IN	NA	Cr6+: Negative
66	Green cladding PCB board (tested as whole)	BL	BL	BL	BL	IN	PBBs: ND / PBDEs: ND
68–71	Type-A USB connector components	BL	BL	BL	BL	BL / NA	NA
76–81	Type-C USB connector components	BL	BL	BL	BL	BL / NA	NA

Legend: BL = Below detection limit by XRF; IN = Inconclusive by XRF, requires chemical confirmation; ND = Not Detected by chemical analysis; NA = Not applicable for this substance/material combination; Negative = Hexavalent chromium Cr6+ not detected.

All 81 components passed. No restricted substance exceeded the maximum concentration values defined by the directive.

Standards & Compliance

The testing programme followed a multi-method analytical approach aligned with the current IEC 62321 series of standards, which are the internationally recognised methods for determining restricted substances in electrotechnical products. The specific standards applied are listed below.

Standard	Scope	Analytical Method
IEC 62321-3-1:2013	Screening — Lead, mercury, cadmium, total chromium, total bromine	X-ray Fluorescence Spectrometry (XRF)
IEC 62321-4:2013+AMD1:2017 CSV	Mercury (Hg) determination	ICP-OES
IEC 62321-5:2013	Lead (Pb) and cadmium (Cd) determination	ICP-OES
IEC 62321-7-2:2017 and/or IEC 62321-7-1:2015	Hexavalent chromium (Cr6+) determination	UV-Vis spectrophotometry
IEC 62321-6:2015	Polybrominated biphenyls (PBBs) and polybrominated diphenyl ethers (PBDEs)	GC-MS
IEC 62321-8:2017	Phthalates (DEHP, BBP, DBP, DIBP)	GC-MS

The governing regulatory framework is the EU RoHS Directive 2011/65/EU (Restriction of the use of certain Hazardous Substances in electrical and electronic equipment) as amended by (EU) 2015/863, which expanded the list of restricted substances from 6 to 10 by adding four phthalates: DEHP, BBP, DBP, and DIBP. The ETENWOLF CL5 was tested against all 10 restricted substances and passed each criterion.

Validity & Certification Body

This test report was prepared and signed by Hugo Chen on behalf of Waltek Testing Group (Shenzhen) Co., Ltd. Waltek is a globally recognised testing and certification laboratory providing compliance services for electronics and electrical products.

Field	Detail
Report Number	WTH26X01027993C
Date of Issue	2026-02-27
Signed By	Hugo Chen
Issuing Laboratory	Waltek Testing Group (Shenzhen) Co., Ltd.
Laboratory Address	1/F., Room 101, Building 1, Hongwei Industrial Park, Liuxian 2nd Road, Block 70, Bao’an District, Shenzhen, Guangdong, China
Telephone	+86-755-33663308
Fax	+86-755-33663309
Email	[email protected]
Website	http://www.waltek.com.cn

RoHS test reports of this type do not carry a fixed expiry date in the same manner as type-approval certificates. However, the report reflects the composition of the product batch sampled on 2026-01-31. Any material or component changes to the CL5 design after this date would require a new assessment to maintain compliance claims. Buyers, importers, and authorised representatives are advised to retain this report as part of their technical file supporting EU market access.

Frequently Asked Questions

What does it mean that the ETENWOLF CL5 passed RoHS testing?: A RoHS pass means that all 10 substances restricted under EU Directive 2011/65/EU and its amendment (EU) 2015/863 — including lead, mercury, cadmium, hexavalent chromium, PBBs, PBDEs, and four phthalates — were found at or below the maximum permitted concentration values in every tested component of the CL5. This allows the product to be legally placed on the EU market.
Which laboratory conducted the testing, and is it accredited?: Testing was performed by Waltek Testing Group (Shenzhen) Co., Ltd., an internationally recognised third-party testing laboratory based in Shenzhen, China. Report number WTH26X01027993C was issued on 2026-02-27 and signed by Hugo Chen on behalf of the laboratory.
How many individual components were tested in the CL5?: At least 81 individually identified components were tested, covering the full range of materials present in the CL5 — including plastics, rubbers, metals, PCB boards, solder joints, LEDs, SMD components, wire jackets, and USB connectors. All components returned compliant results.
What is the difference between a BL result and an IN result in the test table?: BL (Below Limit) means XRF screening detected the substance at a level below the threshold requiring further investigation — no chemical confirmation was needed. IN (Inconclusive) means XRF detected a signal that could not rule out a restricted substance at that stage, so chemical confirmation testing (ICP-OES, UV-Vis, or GC-MS) was performed. All IN-flagged components in this report passed their confirmatory chemical tests, with results such as Cr6+: Negative and PBBs/PBDEs: Not Detected.