Document Overview
Key Findings The ETENWOLF P400 Electric Balloon Pump passed ISTA-2A transport vibration testing across all three samples, with normal appearance and full functionality confirmed after 1 hour of random-mode vibration in X, Y, and Z axes. Test Standard: ISTA-2A Test Mode: Random vibration, 3 axes…
- Document type
- Test Report
- Prepared by
- Jessica Lin
- Published
- Last reviewed
- Topics
- Mechanical Reliability
Key Findings
The ETENWOLF P400 Electric Balloon Pump passed ISTA-2A transport vibration testing across all three samples, with normal appearance and full functionality confirmed after 1 hour of random-mode vibration in X, Y, and Z axes.
- Test Standard: ISTA-2A
- Test Mode: Random vibration, 3 axes (X, Y, Z)
- Duration: 1 hour
- Vibration Frequency: 4 Hz
- Test Speed (CMP): 240 G
- Vibration Amplitude: 25.4 mm
- Samples: 3 PCS
- Verdict: Pass — appearance and function normal post-vibration
Test Overview
| Field | Details |
|---|---|
| Report Title | Vibration Test Report |
| Report No. | 2025041701 |
| Date | 2025-04-17 |
| Page | 1 |
| Product Name | B7 Electric Balloon Pump (P400) |
| Manufacturer | BTK |
| Surface Treatment | / |
| Sample Quantity | 3 PCS |
| Test Standard | ISTA-2A |
| Test Reason | New Product |
| Test Objective | To verify the resistance of the sample under transportation and use environment vibration conditions |
| Laboratory Environment | Temperature: 22°C; Humidity: 55% RH |
Test Equipment & Setup
| Parameter | Value |
|---|---|
| Instrument Name | Vibration Testing Machine |
| Test Mode | Random Mode |
| Test Duration | 1 H |
| Random Directions | X, Y, Z |
| Vibration Frequency | 4 Hz |
| Test Speed (CMP) | 240 G |
| Vibration Amplitude | 25.4 mm |
| Test Requirement | Performance evaluation under vibration environment; verify stability and durability during use |
Test Procedure
- Pre-test inspection: Visually inspect all 3 samples for any pre-existing damage to appearance and verify normal power-on function before testing begins.
- Sample placement: Position samples on the vibration table per the vibration placement diagram (振动摆放图) and configure the vibration control diagram (振动控制图).
- Vibration test execution: Run vibration testing machine in Random Mode for 1 hour at 4 Hz frequency, 240 G CMP speed, and 25.4 mm amplitude, cycling through X, Y, and Z axes.
- Post-test inspection: Power on each sample immediately after test completion and inspect for appearance defects, structural damage, or functional abnormalities.
- Acceptance criteria: Samples must power on normally and show no damage to appearance or functional degradation to receive a Pass judgment.
Test Data & Results
| Stage | Observation |
|---|---|
| Pre-vibration | Samples inspected and placed per vibration placement diagram; vibration control diagram configured |
| During vibration | Random mode vibration applied across X, Y, Z axes at 4 Hz / 240 G CMP / 25.4 mm amplitude for 1 hour |
| Post-vibration | Powered on normally (开机正常); appearance and function confirmed normal |
Overall test result: After transport vibration testing of the B7 (P400) samples, appearance and function were normal. All 3 samples passed.
Conclusion
| Item | Details |
|---|---|
| Test Result | After transport vibration testing, the B7 (P400) samples showed normal appearance and function |
| Standard Applied | ISTA-2A |
| Test Conditions | Random mode, X/Y/Z axes, 4 Hz, 240 G, 25.4 mm amplitude, 1 hour, 22°C / 55% RH |
| Samples Tested | 3 PCS |
| Judgment | Pass |
Document Information
| Role | Name (Pinyin) |
|---|---|
| Approval (核准) | Mai Shaoqiang |
| Review (审查) | Zhang Ronggui |
| Tester (试验人) | Li Guanghua |
| Form Number | BTK-R-Q-087A/1 |
Frequently Asked Questions
What standard was used for the P400 balloon pump vibration test?
The ETENWOLF P400 Electric Balloon Pump was tested to the ISTA-2A standard, which simulates transportation and handling vibration environments to verify product durability and stability.
Did the P400 balloon pump pass the transport vibration test?
Yes. All 3 samples of the P400 Electric Balloon Pump passed the ISTA-2A transport vibration test. After 1 hour of random-mode vibration across X, Y, and Z axes, all units powered on normally with no appearance damage or functional abnormalities.
What were the vibration test conditions for the P400?
The test ran in random mode for 1 hour at a vibration frequency of 4 Hz, test speed of 240 G (CMP), and vibration amplitude of 25.4 mm. All three directional axes — X, Y, and Z — were covered. The laboratory environment was 22°C and 55% RH.
How many P400 samples were tested in the vibration report?
Three (3) PCS of the B7 / P400 Electric Balloon Pump were included in this transport vibration test conducted on 2025-04-17, report number 2025041701.